Menu
Your Cart

OGEE 3 LIP CUTTER

OGEE 3 LIP CUTTER
OGEE 3 LIP CUTTER
PACK SIZE
The price displayed for this product is the unit price of the product. Where a PACK SIZE is indicated, this refers to the recommended ordering quantity and is also indicative of how many of these products are packaged in a box.
  • Stock: 7
  • Model: KP831010
  • Weight: 0.44kg
  • Pack Dim: 78.00mm x 76.00mm x 76.00mm
  • UPC: 6009600402119
Price:
R 1,526.11
Ex VAT: R 1,327.05

Available Options

Pro-Tech. South African favourite for over 30 YearsSpindle cutter - Ogee lip

 

Tungsten Carbide - 3 wing

The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4" or 1/2" spindle shaft.

The cutter is a counter-profile cutter. When properly aligned, it will allow two panels to join together without the use of a secondary cuttter. The ogeevprofile assists with alignment during assembly and adds a greater glue surface, resulting in a stronger joint.

KP800020 - 3/4" - 1/2" spacer rings

Important:

  • Make sure the spindle moulder has a table opening of at least Ø 140mm.
  • Designed for spindle moulders equipped with either a 1/2" or 3/4" spindle shaft.

Spindle Safety

Spindle cutters can potentially be dangerous and should deserve your attention and respect.

Use push sticks or a push block to position your hands a safe distance from the spindle cutter.

Never climb-cut. Always feed the stock against the rotation of the cutter (see illustration).

Avoid moulding small stock. Instead, mould a larger piece and cut it to size afterwards.

Always use a guard. If the fence didn’t come with a guard, make your own.

Never start the spindle with the cutter in contact with the material.

Don’t force the cutter or overload the machine. Excessive heat is an enemy.

The spindle moulder needs to have a power feeder or feather boards fitted to apply sufficient feeding pressure.

Fit the cutter on the lowest point of the spindle shaft.

Be sober and not under the influence of medicine that causes a lack of concentration.

Make sure the spacer rings on the spindle shaft are locked in place correctly.

Tidy up your workshop to ensure the ability to move freely with enough room around the spindle moulder.

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear Gloves Eye Protection Hearing Protection Dust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

To use spindle cutters safely (and to get the best results from your spindle), the cutters need to be installed properly on the spindle shaft. Improper installation of your cutter can cause excessive chatter and could increase the likelihood that the bits will break when in use. There is also a risk of having the cutter "cold welded" to the spindle shaft.

First of all, before beginning any moulding operation, check your cutter to make sure that it is clean and most of all, sharp. If the bit is dull, chipped, is excessively burnt or has any other defect, it should be sharpened or replaced before use.

Pro-Tech. South African favourite for over 30 Years
Description Specification
Cutter profile Ogee lip
Arbor 3/4"
Wings 3
Cookie Notice:
We Use Cookies... In addition to the cookies that are strictly necessary for the operation of this website, Vermont Sales uses cookies and other tracking tools to remember your preferences and to measure our website performance. Rest assured, your information is safe with us and we will NEVER share it with any other party. Privacy Policy